subaru technology in detail

(English, Русский)

Symmetrical AWD

(Edit)

(Adapted from Subaru's German-language article)

In September 1972, Subaru introduced the Leone Station Wagon AWD with selectable four-wheel drive as standard. Subaru describes it as the first all-wheel-drive passenger car to go into mass production. In the original article, the company reported that it had built more than ten million all-wheel-drive passenger cars worldwide.

Until the early 1960s, all-wheel drive was associated mainly with military, construction and dedicated off-road vehicles. It gave those vehicles traction in difficult terrain, but they were slow and did not handle corners well. As engines became more powerful and cars faster in the 1970s, driving all four wheels offered a way to put more of that power to the road in a controlled manner.

Subaru - Pioneer of All-Wheel Drive

(Edit)

Tohoku Electric Supply Company, which supplied electricity in Tohoku Prefecture in northern Honshu, needed a vehicle its employees could use to reach their worksites safely in winter. Subaru developed the Leone Station Wagon AWD and delivered it in September 1972. Its ability to handle snow and mountain roads appealed to other companies in Japan, and it also sold well abroad. The Leone became the basis for Subaru's all-wheel-drive technology. Audi introduced the original Quattro in 1980, eight years after the Leone.

September 1972: The era of all-wheel drive begins.

(Edit)

Inside and out, the Subaru Leone Station Wagon AWD resembled the front-wheel-drive models. It added selectable four-wheel drive. When engaged, a dog clutch made a rigid mechanical connection between the normally driven front axle and the rear axle.

Technical specifications for the Subaru Leone Station Wagon AWD:

  • Length / width / height: 3995mm x 1500mm x 1385mm
  • Weight: 855 kg
  • Engine: Water-cooled four-cylinder boxer engine EA63S
  • Bore x stroke: 85 mm x 60 mm
  • Displacement: 1361 cubic centimeters
  • Compression ratio: 8.5: 1
  • Max. power: 53 kW (72 PS) at 6,400 rpm
  • Max. torque: 100.06 N·m at 3,000 rpm (Subaru's specification)
  • Gearbox: Four-speed manual transmission
  • Drive: Switchable all-wheel drive. A dog clutch rigidly couples the normally driven front axle to the rear axle.
  • Suspension: independent front suspension with MacPherson struts and independent rear suspension with semi-trailing arms

System advantages of all-wheel drive

(Edit)

Subaru highlights three benefits of all-wheel drive: traction, handling and stability. Driving all four wheels spreads the tractive effort across more of the available tire grip, which can make the car's response under power more predictable.

A tire uses the available grip at the road surface both to transmit drive and to generate the lateral force needed for cornering. In the comparison Subaru describes, spreading the same drive demand across four tires reduces the demand on each driven tire and can leave more grip available for cornering under power.

Subaru illustrates this with a simplified example. If the engine supplies 100 PS and each driven wheel can transmit the equivalent of 30 PS before spinning, an equal split across two driven wheels gives 50 PS per wheel, above the limit. An equal split across four driven wheels gives 25 PS per wheel, below the limit. The example describes traction under power under those assumptions.

Systematic Symmetry: Subaru "Symmetrical AWD"

(Edit)

Subaru's Symmetrical AWD pairs a boxer engine with a symmetrical drivetrain. In a boxer engine, the cylinders face each other across the crankshaft and the pistons move horizontally in opposing pairs. Subaru credits this layout with a stiffer cylinder block and a flat, short, compact engine. A short, rigid crankshaft allows high engine speeds, and the engine runs smoothly up to its rated speed without balance shafts. The low engine profile helps lower the car's center of gravity, reducing body roll and improving stability in corners.

The longitudinally mounted boxer engine, transmission, propeller shaft and rear differential are aligned along the vehicle's centerline. The layout is symmetrical from left to right, and major components are concentrated between the axles. Subaru associates this layout with balanced weight distribution and predictable handling.

The symmetrical layout leaves room on both sides of the engine compartment for structural members that extend from the passenger compartment to the bumper and help absorb energy in a frontal impact. Subaru says the low engine mounting allows the engine to move beneath the floor instead of intruding into the passenger compartment.

The future: Improving the vehicle dynamics of all-wheel drive vehicles.

(Edit)

At the time of the article, Subaru was developing closer coordination between Symmetrical AWD, Vehicle Dynamics Control, Yaw Moment Control and Tire Force Control. It also identified improvements to the center differential, an electronically controlled center limited-slip differential, and refinements to the front and rear limited-slip differentials as ways to improve handling.

The equation of the future: Subaru = all-wheel drive

(Edit)

Subaru describes the Leone Station Wagon AWD of September 1972 as the starting point for the development of Symmetrical AWD. As of 2005, the company regarded its longitudinal, left-right symmetrical layout as the basis for further all-wheel-drive development.

Subaru all-wheel drive systems: Consistent evolution from 1972 to 2005.

(Edit)

Subaru uses different all-wheel-drive designs for manual and automatic transmissions.

Subaru all-wheel drive systems with manual transmission

(Edit)

1972: Mechanically engageable all-wheel drive.

The simplest arrangement is selectable four-wheel drive. In the Subaru Leone AWD, engaging a dog clutch rigidly couples the normally driven front axle to the rear axle.

1980: Mechanically engageable all-wheel drive and "dual-range"

Subaru continued to develop its original selectable four-wheel-drive system. The 1980 Subaru 1800 used a manual transmission with selectable four-wheel drive and Dual Range reduction gearing. Pulling the lever moves a sliding sleeve in the gearbox to engage a gear pair and drive the rear axle. The second lever position engages the reduction gear for low range.

1983: Pneumatically engageable all-wheel drive.

The Libero (1983) and Justy (1984) also used manual transmissions with selectable four-wheel drive. On these models, a button on the shift lever operates an electro-pneumatic actuator. A solenoid valve applies engine vacuum to one side of a diaphragm on the gearbox while atmospheric pressure acts on the other side. The pressure difference moves a selector shaft attached to the diaphragm. The shaft moves a sliding sleeve that engages the drive to the rear axle.

1987: Permanent all-wheel drive.

Subaru introduced permanent all-wheel drive with the XT coupe at the 1987 Frankfurt Motor Show. For the first time, Subaru offered all-wheel drive in the same model with either a five-speed manual or a four-speed automatic transmission. In the manual version, the center differential splits drive evenly between the front and rear axles. When the axles rotate at different speeds, the differential can be locked electromechanically. An electric switch actuates a mechanical locking pawl that fully locks the differential.

1988: Permanent all-wheel drive with viscous lock.

The first-generation Legacy was Subaru's first model to use a center differential with a self-locking viscous coupling. The basic transmission design is the same as that of the XT. In the Legacy, the viscous coupling in the center differential progressively limits slip as the difference in rotational speed between the axles increases, up to full lock of the differential. At the time of the article, Subaru still used a center differential with a viscous coupling in its manual models.

2005: STi-AWD with planetary gear center differential, helical LSD, DCCD.

The Impreza WRX STi, the basis for the Impreza WRC, adapts this design for performance use. Its six-speed transmission has a planetary center differential. With the clutch released, the front-to-rear torque split is 36:64. The driver can use the rotary DCCD (Driver Controlled Center Differential) switch to adjust the degree of lock applied to the planetary gearset by an electromagnetic clutch. Subaru lists a 50:50 split at maximum lock for this system. A helical limited-slip front differential improves front-wheel traction while cornering.

Subaru all-wheel drive systems with automatic transmission

(Edit)

1981: Automatic transmission with a multiplate four-wheel-drive transfer clutch

The multiplate transfer four-wheel-drive system (MP-T) uses hydraulic pressure from the automatic transmission. The driver can engage four-wheel drive while moving by pressing a button. A seven-plate clutch is mounted on the output shaft connected to the rear driveshaft. When four-wheel drive is selected, transmission pump pressure engages the clutch so it can transmit torque to the rear driveshaft. This lets the system compensate for rotational speed differences between the front and rear wheels. In Auto-4WD mode, Subaru's description identifies brake application and windshield-wiper operation as inputs that activate clutch pressure.

1987: Permanent all-wheel drive.

In the Subaru XT with the four-speed ACT-4 (Active Control of Torque) automatic transmission, a pair of equal-sized gears transmits drive mechanically to the front axle. A hydraulically actuated wet multiplate clutch transmits drive to the rear axle.

1989: ECVT transmission and selectable all-wheel drive.

On the 1989 Justy with ECVT, a button on the shift lever engages four-wheel drive. A hydraulic actuator moves a selector shaft, which engages a sliding sleeve to connect the transfer drive.

1991: Permanent all-wheel drive with VTD.

Subaru introduced the revised automatic transmission with VTD (Variable Torque Distribution) in the 1991 Gran Turismo SVX. The system uses a planetary center differential and a rear differential with a viscous coupling. The normal front-to-rear split is 36:64. As grip changes, the electronics adjust the torque distribution. When the front and rear axles rotate at different speeds, a hydraulic multiplate clutch progressively limits differential action in the planetary gearset. The rear viscous coupling limits slip between the rear wheels.

1998: Permanent all-wheel drive with VTD and Vehicle Dynamics Control.

In 1998, Subaru added VTD and Vehicle Dynamics Control (VDC) to higher-trim Legacy models. The mechanical design of VTD stayed the same. Improved sensors and communication over the CAN bus enhanced electronic control.

2004: Permanent all-wheel drive with optimized VTD and Vehicle Dynamics Control.

The new five-speed VTD automatic uses a planetary gearset and a multiplate locking clutch to vary the torque delivered to the front and rear axles over a broad range. The Vehicle Dynamics Control (VDC) unit communicates with the transmission control unit. If VDC detects understeer or oversteer, it signals the transmission control unit, which adjusts the clutch to reduce drive torque to the axle that is losing grip.

All Legacy 3.0s from model year 2004 onwards have this system.

Technical details:

(Edit)

Structure and function of the multi-plate lock (automatic transmission with VTD)

(Edit)

Transmission output torque enters the planetary gearset through the primary sun gear. The planet gears are carried by the planet carrier, which is connected to the output gear for the front axle. The rear planet gears drive the rear output shaft through the secondary sun gear. The multiplate locking clutch limits differential action as the rotational speed difference between the axles increases. The normal 36:64 front-to-rear torque split can be varied progressively by adjusting the clutch. The degree of lock depends on the speed difference and can reach 100 percent. The German source reports a 60:40 front-to-rear split at full lock, distinct from the 50:50 figure it gives for the 2005 WRX STi DCCD system.

Design and function of the multi-plate clutch (ACT-4 automatic transmission)

(Edit)

The wet multiplate clutch contains alternating outer steel plates and inner friction plates. The outer plates are mechanically coupled to the planet carrier. The inner plates are mounted on a plate carrier coupled to the rear output shaft. A hydraulic piston in the final-drive housing clamps the plate pack. A map-controlled solenoid valve regulates piston pressure in response to pulsed signals from the transmission control unit. The controller uses signals from speed sensors 1 and 2 and from Vehicle Dynamics Control to assess vehicle load and any rotational speed difference between the axles. Increasing hydraulic pressure increases the clamping force on the plates and lets the clutch transmit more torque to the rear axle.

Structure and function of the viscous lock (manual transmission with center differential)

(Edit)

Inside the sealed housing, alternating plates are fixed against rotation relative to either the hub or the housing. The plates run in silicone oil and do not touch during normal relative rotation. In Subaru's example, the outer plate rotates while the inner plate is stationary. Oil in contact with the outer plate moves with it.

A difference in rotational speed between the housing (outer plates, connected to the front axle) and the hub (inner plates, connected to the rear axle) shears the silicone oil between the plates. This resists motion at the faster plate and transmits torque to the slower one. Subaru compares the effect to pulling a spoon through honey. Move it slowly and the jar stays put. Pull it quickly and it drags the jar along.

A sustained speed difference heats the silicone oil. As the oil expands, pressure rises in the sealed housing and can force the inner and outer plates together. The coupling can then lock the center differential. Subaru calls this the hump effect. When the speed difference subsides and the coupling cools, the pressure drops and the coupling returns to normal operation.

Helical LSD

(Edit)

A helical limited-slip differential uses gears with helical teeth. Under load, the tooth geometry generates reaction forces against the housing and increases friction at the contact surfaces. Subaru describes this as a torque-sensing design in the Torsen family.

The limited-slip action resists relative motion between the wheels and biases torque toward the wheel that can transmit more of it. When pulling away on a surface with uneven grip, the differential can redistribute torque to the wheel with better grip. In a corner under power, it still allows the wheels to turn at different speeds. Its locking action depends on friction under load, which the source describes in terms of Coulomb friction. Subaru notes that the tendency to resist unequal wheel speeds can promote understeer under power. The German text gives conflicting explanations of how the speed difference affects locking.

µ-Estimator:

(Edit)

The µ-estimator uses available vehicle signals to calculate tire slip and estimate available grip. Subaru uses that estimate together with Vehicle Dynamics Control and yaw-moment feedback to adjust center differential lock on slippery roads and torque distribution on dry roads.

The estimator uses existing sensors. It applies an adaptive parameter-identification method to estimate tire characteristics that depend on µ, the tire-road friction coefficient. It accounts for changes associated with lateral acceleration and uses those changes when the usual identification input provides too little information. The controller adjusts the estimated tire characteristics, derives an estimate of µ from them, and uses it to set the baseline torque split.

On roads with continuous snow cover, Subaru evaluates steering response using an instantaneous stability factor K derived from steering angle, yaw moment and vehicle speed. K is negative for oversteer and positive for understeer. Subaru reports that neutral handling or oversteer occurs relatively often with the center differential open, while pronounced understeer occurs relatively often with it locked.

Subaru introduced a correction to the instantaneous stability factor. The correction tends to be small or negative when the vehicle frequently oversteers. In the VTD system described in the article, Vehicle Dynamics Control uses the estimated µ to adjust torque distribution, with yaw-moment feedback to improve handling and stability.

Sources: http://www.subaru-presse.de/symmetrical-awd.html" class="external" target="_blank">Subaru Deutschland's original article (archived), German reprint and Leone specifications, Subaru Deutschland's Leone history, and Subaru's 40th anniversary production figures.

This is a Wiki, so feel free to correct any factual or grammatical error. Test here before posting.

There are no comments yet

Leave a Comment


?
? ?